Signal Processing
DSP is applied nondestructively and in real time to individual tracks in a playlist, so it does not affect the original audio files recorded on the hard disk. Also, deleting a track from a playlist does not delete its parent audio file from the hard disk. However, deleting will cause all of your DSP settings to be lost for that track. According to Alesis, Version 2.0 software for MasterLink allows backing up tracks in a playlist backup/restore mode. To avoid losing work that may be needed if and when an indecisive client decides to reinstate a deleted track, you’ll need to add the track to an alternative playlist—a holding tank for ideas, if you will—and manually re-enter DSP settings before you delete the track from its original playlist. V. 2.0 software is said to allow copying and pasting of DSP settings between tracks on different playlists.

DSP is applied to tracks in six blocks arranged in the following, immutable order: track gain, compressor, parametric EQ, limiter, track fades and normalizer. Individual DSP blocks can be toggled on/off independently. My only complaint is that, for most applications, I would rather have EQ come before compression so that applied boost doesn’t undo dynamic range adjustments. That said, MasterLink’s dynamics processing and EQ sound downright superb, and the range and incremental control of parameter values will satisfy even the most finicky mastering engineer.

MasterLink’s compressor is clean and extremely transparent. Even the hard knee mode is relatively free of amplitude modulation artifacts. Simply put, this is one of the best digital stereo program compressors I’ve heard.

The compressor offers threshold, ratio, makeup gain, attack, release, key (channel master), knee (choice of hard and four soft knee modes), detect (peak or RMS) and meter parameters. The latter offers six combinations of input/output/gain reduction metering.

Unfortunately, the compressor’s makeup gain can only boost and not attenuate, and the downstream EQ block has no output gain control. Whenever EQ boost clips the downstream limiter, you must attenuate levels in the track gain block—necessitating a resetting of the compressor’s threshold. It’s a minor hassle.

MasterLink’s sweet-sounding EQ block offers both parametric and low/high shelving curves. On the downside, there are only three bands and they don’t have independent bypasses. But happily, all three bands cover 20.22 to 20.22k Hz in very fine steps, and boost/cut is adjustable in exacting 0.25dB increments. Q is adjustable from 0.1 to 18, making notch filtering and broad tonal shaping a snap.

MasterLink’s look-ahead peak limiter is reminiscent of the Waves L1 in that it combines a brick-wall, :1 limiter with a maximizer function for setting your output “ceiling.” MasterLink’s limiter sounds outstanding. It’s extremely transparent and can really beef up a mix.

Fade-in and -out times can be adjusted for each track in 10ms or 1-second increments. Linear fade, normal logarithmic and inverse log shapes are offered, and they all sound very smooth.

MasterLink also offers a real-time (vs. file-based) normalizer, allowing changes to be made after upstream signal processing settings are altered.

On my wish list for future software updates: a global bypass for all DSP, and multipoint I/O metering before/after each DSP module (to safeguard against potential clipping at various points along the audio path). Notably, the compressor block already provides such metering.

Burn, Baby, Burn
After you’re finished tweaking the EQ, compression and other settings, signal processing is written to each track in a manner similar to “bouncing to disk” in a DAW. The rendered playlist is recorded to a reserved, “invisible” area of the hard disk so that it can be burned to CD multiple times without the need to re-render. Rendering only occurs with Red Book CDs—MasterLink does not render in high-definition 24/96 mode. The time display still shows elapsed/remaining time for a single track or the entire playlist while the CD is being burned, and the current track number also changes to reflect your progress.

MasterLink can read and write both Red Book (16-bit, 44.1kHz) CDs and proprietary CD24 CDs. CD24 discs can be written to and played back at any of the 12 resolutions that the hard disk can record at, and is not limited to just 24-bit/96kHz data. Only disk-at-once mode is supported.

When you write high-resolution audio to a Red Book CD in MasterLink, the audio is automatically noise-shaped and/or sample-rate converted down to 16-bit, 44.1 kHz on its way to CD. However, the high-res audio files on the hard drive remain unchanged. CD24 discs are played back by MasterLink at their original sample rate and word length.

MasterLink writes Red Book CDs at 4x speed and CD24 discs at 2x speed onto standard CD-R blanks. A 650MB disc will hold a maximum of 19 minutes of 24/96 audio, and the recording process takes about 36 minutes.

File Exchange
Alert readers will notice that MasterLink has no SCSI connectors. How does MasterLink exchange data with DAWs?

MasterLink’s CD24 mode records .AIFF sound files in an ISO-9660 CD-ROM disc format along with proprietary information, making the CD24 discs compatible with CD-R and CD-ROM drives. Most computer-based audio editing programs can recognize .AIFF files, raising the possibility of opening a CD24 disc in a DAW to perform further editing. However, Macs cannot recognize the file type and creator info on CD24 discs made with MasterLink’s V. 1.0 software. (This is not an issue with PCs.) This should be corrected with the release of V. 2.0 software, and CD24 discs should be fully compatible with Macs. Both Windows and UNIX operating systems are also currently supported.

How about going in the other direction, from DAW to MasterLink? MasterLink can only recognize Red Book audio or CD24 discs; it cannot read .AIFF files created in a DAW. To transfer high-resolution audio or anything other than Red Book audio files from a DAW into MasterLink, you must play the DAW’s audio files in real time and record—preferably via digital I/O—to MasterLink’s internal hard drive. MasterLink can also copy individual tracks, one at a time, from Red Book CDs to its hard drive. V. 2.0 software will reportedly be able to copy all CD tracks at once.

Conclusions
MasterLink provides an enormous yet cost-effective upgrade to outdated DAT decks and CD burners in a portable, all-in-one package. The built-in DSP sounds so good, many users will choose to use it in lieu of their outboard gear and DAW plug-ins. Top-notch sound quality, ultrafine parameter control, support of numerous high-resolution formats, backwards compatibility and the robust error correction of the CD-ROM format give MasterLink a strong shot at establishing a new industry standard for master delivery and archiving. File exchange issues should be resolved with the release of V. 2.0 software, leaving the analog front-end’s limited headroom as the only major barrier to full professional acceptance. If you can work around that, MasterLink is a slam dunk.

Alesis, 1633 26th St., Santa Monica, CA 90404; 800/5ALESIS; www.alesis.com.

Michael Cooper is the owner of Michael Cooper Recording, located outside the small resort town of Sisters at the base of the Oregon Cascades.

Back to Page 1; Back to TOP

Reprinted with permission from Mix Magazine, June, 2000
© 2000, Intertec Publishing, A Primedia Company All Rights Reserved